20MnCrS5. 1,7149. 0,020 ÷ 0,040. CONCENTRATION LIMITS OF THE ELEMENTS THAT ARE NOT INDICATED IN THE TABLE CAN BE DEDUCED IN THE EN 10020 REGULATION. 36NiCrMo16, 39NiCrMo3, 40NiCrMo7 - alloy steels39NiCrMo3 - 1.6510 - Chromium-nickel-molybdenum steel:40NiCrMo7 - AISI 4340 - 40HNMA - 40NiCrMo6 - 1.6565 - 40NiCrMo8-4 The grades of this carbon structural steel feature greater tensile strength, plasticity, crack resistance at dynamic loads, better hardening capacity, and uniform properties across the entire cross section.
39NiCrMo3 Steel for Quenching and Tempering 1.6510 38NCD4. Application. 39NiCrMo3 Steel with high hardening capacity and good toughness, which allows to achieve optimum mechanical properties with dimensions up to approx. 80mm. 39NiCrMo3 Steel used on heavy-duty machinery parts, automotive accessories, other motor vehicles, engine parts, shafts, etc. 40Cr Steel Equivalent Mechanical Properties Chemical Alloy special steel Chemical composition of steel 39NiCrMo3 (1.6510), Standards of steel 39NiCrMo3 (1.6510) Mechanical Properties of steel 39NiCrMo3 (1.6510) Equivalent grades of steel 39NiCrMo3 (1.6510) steel 39NiCrMo3 (1.6510) Tensile Strength, Elongation, Proof strength , Hardness. 39NiCrMo3 / 1.6510 - SteelNumber - Chemical composition 40Cr 40NiCrMo7-3Used for large axles, machine componenets etc. that require high tensile strength and high toughness. Can be flame or induction hardened. 6514 in intended for ASTM A320 L43 fasteners in low-temperature service. Ovako 355B The grade is inside the SAE 4340 specification but is slightly enhanced with Vanadium for improved tempering resistance.
The maximum stress value of EN 10083-3 39 NiCrMo 3 EN 10083-3 before tensile fracture is called strength limit or tensile strength. EN 10083-3 39 NiCrMo 3 physical The physical properties of EN 10083-3 39 NiCrMo 3 EN 10083-3 steel incorporate high quality, low weight, solidness, ductility and protection from erosion. EN10083-3 39NiCrMo3 High Alloy Steel Plate - Bebon steelsEN10083-3 39NiCrMo3:0.35-0.43:0.4:0.5-0.8:0.025:0.035:0.6-1:0.15-0.25:Grade:Mechanical Property :Yield Strength(MPa) Tensile Strength(MPa) % Elongation min:EN10083-3 39NiCrMo3: EN19 Steel 4140 1.7225 SCM440 42CrMo4 - OTAI Tensile strength of EN19 Engineering steel:775-1075 N/mm². Engineering steel material EN19 hardness in HRC:Flame or induction hardening can give a case hardness of 50 HRC or higher. EN19 equivalent material with AISI 4140, DIN 42CrMo4 EN 1.7225, GB 42CrMo, JIS SCM440C alloy engineering steel. Mechanical properties of steel EN19 (1.7225)
For stainless steel 1.4310 the tensile strength is 15% less, according EN 10270-3-NS. The max bending stress is taken 0.7Rm, the max torsional stress 0.4Rm, when statically loaded. Statically loaded is defined for up to 20 to 50 thousand load cycles. Quenched and tempered steels (EN 10083-3) - M.T. Acciai s.r.l.39NiCrMo3 hardened and tempered:rolled forged turned drawn / ground:20-300 340-1000 5-160:39NiCrMo3 hardened and tempered high machinability:rolled:20-300:39NiCrMo3+Pb hardened and tempered:rolled drawn / peeled h11:20-200 5-100:C45 natural:rolled forged turned draw / ground:20-330 340-1000 5-150:C45 hardened and tempered:rolled:30-200:40NiCrMo7 (L43~) hardened and Steel Chart EN Series Steel Chart Chemical Analysis EN-9. Bolts, M/C Tool, Axial shaft. EN-19 (V 320) Components of mediums & large cross section, requiring high tensile strength & toughness for automatic engineering and gear & engine construction such as Crane Shafts Steering Knocking Connecting. EN-24 (V 130) Highly stressed components of large cross section for aircraft, automotive & general
39NiCrMo3 datasheet, 39NiCrMo3 mechanical properties, chemical element 39NiCrMo3, technical specifications of 39NiCrMo3 steel material properties. 39NiCrMo3 performance specifications. Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity