[email protected]

AISI 1018 Carbon Steel - Waldun Steel

AISI1018 Carbon Steel Mechanical Property. 1.Tensile strength:410MPa 2.Yield point:245MPa 3.Percentage reduction of area after fracture:55% 4.Elongation after fracture:25%. AISI1018 Carbon Steel Delivery Condition. 1.Shape:Round/Square / Flat/Shafts/Rollers/Blocks 2.Surface condition:Black surface/Bright surface 3.Heat Treatment:Normalized/Annealed AISI 1020 Carbon Steel - Waldun SteelWhat is the Yield Strength of Low Carbon Steel? Yield strength is the property of stress in which specific amounts of plastic deformation is produced. It is the capacity of a certain material to undergo reversible elastic strain or to be deformed with it capable of being formed back to its original state. The yield strength of most low carbon steels is at around 250 MPa, or about 36,200 ppi.

Carbon Steel:Properties, Examples and Applications -

High-carbon steel has a carbon content of 0.60 1.25 wt.% and a manganese content of 0.30 0.90 wt.%. It has the highest hardness and toughness of the carbon steels and the lowest ductility. High-carbon steels are very wear-resistant as a result of the fact EN9 070M55 Medium Carbon Steel BS970 Standard - EN9/070M55 steel,called 55 Carbon steel, is a common unalloyed medium steel as per British standard BS 970.It has carbon content with 0.50-0.60% which gives it tensile strength between 500-800Mpa when supplied in untreated condition or normalized condition.EN9 is also suitable in the hardened and tempered condition for tensile ranges of R (700-850Mpa),S (775-925Mpa),and T (850 High Durability 20# ASTM A36 Steel Round Bar 1.2344High quality High Durability 20# ASTM A36 Steel Round Bar 1.2344 from China, China's leading a36 steel round bar product, with strict quality control 1.2344 a36 steel round bar factories, producing high quality a36 steel round bar products.

M2 High Speed Steel AISI M2 1.3343 SKH51 - Waldun Steel

M2 steel has superior properties in toughness, wear resistance ,hardness and good machinability. Compared with T1, it is more economic ,its hardness is same as T1 after heat treatment,but its bending strength can reach 4700 MPa, and its toughness and thermo-plasticity are higher than T1 by 50%. Factory hardness:255HB. S355J2/S355J2+N/S355J2G3 - Waldun SteelS355J2 steel is a carbon manganese ,high yield non alloy steel. It is called S355 because of the average minimum yield for this material is 355 Mpa.As a structural steel,it has excellent strength and weldability.It can be readily welded to other weldable steel. For its low carbon equivalent, it possesses good cold-forming properties. SAE / AISI 4150 Steel - Waldun SteelHere are some of the most important properties of the AISI 4150 steel:Tensile Strength:731 MPa or 106,000 psi; Yield Strength:380 MPa or 55,100 psi; Machinability:55 (annealed and cold drawn) Thermal Conductivity:44.5 W/mK; Melting Point:1,427 degrees Celsius or 2,600 degrees Fahrenheit; Is AISI 4130 Stainless Steel?

T1 1.3355 Skh2 High Speed Steel Round Bar and Plate

T1 1.3355 SKH2 High Speed Steel Round Bar and Plate 1:T1 steel introduction T1 tool steel is one of the original tungsten high speed steels, although all tungsten steel grades are used to a limited extent because of the cost and questionable availability of tungsten. What is Strength of Stainless Steels - Yield - UTS Ultimate tensile strengths vary from 50 MPa for an aluminum to as high as 3000 MPa for very high-strength steels. Yield Strength. Yield strength of stainless steel type 304 is 205 MPa. Yield strength of stainless steel type 304L is 170 MPa. Yield strength of ferritic stainless steel skh2 steel, skh2 steel Suppliers and Manufacturers at Product Basic Information:Material AISI T1 Chemical Composition Mechanical Properties(In Quenched & Tempered State) C 0.70-0.80 Tensile strength(MPA) - Si 0.20-0.40 Yield strength (MPA) - Mn 0.10-0.40 Elongation(δ5/%) -- Cr 3.80-4.40 Reduction in Area (ψ/%) - Mo <0.30 Impact (J) - P ≤ 0.030 Brinell Hardness (HBW) <255 cooling with OIL preheating temperature 820-870c S ≤ 0.030 W

AISI T1 Steel 1.3355 HS 18-0-1 SKH2 High Speed Steel

AISI T1 Steel 1.3355 HS 18-0-1 SKH2 2750 High Speed Steel. AISI T1 Steel Reference standard:ASTM A600, DIN 17350, EN ISO 4957, JIS G 4805, GB/T 9943, SS14. AISI T1 steel is a high tungsten high speed tool steel. It is used to high strength, high hardness, high