May 30, 2020 · EN 1.0038 (S235JR) Non-Alloy Steel. EN 1.0038 steel is a carbon (non-alloy) steel formulated for primary forming into wrought products. 1.0038 is the EN numeric designation for this material. S235JR is the EN chemical designation. It can have a moderately low tensile strength and has a moderately low thermal conductivity among wrought carbon or EN 1.0038 Steel S235JR Material Equivalent, Properties Dec 14, 2019 · Chemical Composition (ladle analysis) %, :Standard:Grade:Steel Grade (Steel Number) C:Si:Mn:P:S:Cu:N:EN 10025-2:S235 steel:S235JR (1.0038) 0.17 1.40:0.035:0.035:0.55:0.012:S235J0 (1.0114) 0.17 1.40:0.030:0.030:
Chemical Composition Chemical composition according to EN 10025:1993 (BS EN 10025, 1993) The chemical composition of S235JR is presented in Table 2 as the ladle analysis for long and flat products and the product analysis in % weight. Product analysis is to be taken into consideration when dealing with purchase orders. Q235 vs A36, SS400, E250, S235JR Steel, Q235A, Q235B Dec 08, 2019 · Wiki Q235 vs ASTM A36, S235, SS400 and E250 Steel The following tables show Q235 steel vs A36, SS400, S235JR and E250 steel, they are similar in chemical composition, mechanical properties, and all belong to carbon structural steels. S235 has 3 quality grades, including S235JR, S235J0 and S235J2 S235JR - OvakoChemical composition Variant Cast Weldability C % Mn % P % S % Cu % N % SS 14 13 12:1987 (ref) Std CEV Min - - - - - - Pcm Max 0.20 - 0.050 0.050 - 0.0120 S235JR EN10025-2 (ref) Std CEV 0.35 Min - - - - - - Pcm 0.25 Max 0.17 1.40 0.035 0.035 0.55 0.0120 max max max max S235JR:C max 0,20 % for sizes over 40 mm. Only CEV required in standard
S235JR:C max 0,20 % for sizes over 40 mm. Only CEV required in standard. SS 1312:Not binding recommendation for Mn (0,4 - 0,7) % in standard. S235JR Non-alloy Quality Structural Steel - EN MaterialThe Indicative Chemical Composition of S235JR Steels:The chemical composition of this grade is indicated as under:Maximum percentage of Carbon (C) is 0.22 percent. Maximum percentage of Manganese (Mn) is 1.6 percent. Maximum percentage of Phosphorous (P) is 0.05 percent. Maximum percentage of Sulphur (S) is 0.05 percent. Steel Plate EN10025-2 Grade S235J0 S235JR S275JR S235J2 Steel Plate EN10025-2 Grade S235J0 S235JR S275JR S235J2 S275J2 S355J0 S355JR S355K2 in Large Stock. Mechanical and chemical properties of EN10025-2 S235J0 Chemical composition % MAX THICKNESS(MM) C Mn Si P S N Cu 40 0.17 1.4 ~ 0.03 0.03 0.012 0.55
Steel grade S235JR equivalent GB material is Q235B, steel grade S235JR equivalent JIS material is SS400 / SM400A, steel grade S235JR equivalent DIN material is ST37-2. Then what is steel grade S235JR equivalent ASTM material? Steel grade S235JR equivalent ASTM material is A36 steel. From their chemical composition and mechanical properties, we can easily understand their same Structural Steel - S235, S275, S355 Chemical Composition May 11, 2012 · The chemical composition of structural steel is extremely important and highly regulated. It is a fundamental factor which defines the mechanical properties of the steel. In the following table, you can see the maximum percentage levels of certain regulated elements present in European structural steel grades S235, S275, and S355. Chemical Composition of Structural Steels - S235, S275 and S355. The Chemical composition What is EN 10025 Grade S235JR? - Matmatch
- NamingProperties of S235jrApplicationsEN 10025 S235JR has a specified chemical composition of 0.17 0.20 wt.% carbon (depending on thickness), 1.40 wt.% manganese, 0.55 wt.% copper, 0.012 wt.% nitrogen, 0.04 wt.% phosphorous and 0.04 wt.% sulphur. Plate thickness has a major impact on elongation and yield strength. Elongation ranges from 26 % for plates less than 40 mm thick to 22% for plates thicker than 100 mm but thinner than 125 mm. Yield strength ranges between 360 and 510 MPa for plates less than 100 mm thick, and 350 S235JRG2 / 1.0038 - SteelNumber - Chemical composition Standard:EN 10250-2:2000 Open steel die forgings for general engineering purposes. Non-alloy quality and special steels. Equivalent grades:Go here. Chemical composition % of steel S235JRG2 (1.0038):EN 10250-2-2000. For forgings with an equivalent diameter or thickness > 100 mm the carbon content shall be agreed beetween purchaser and supplier.
Steel grade S235JR is a popular general construction and machine steel that is made in accordance with the EN 10025-2 standard. Classification:Non-alloy structural steel. Products:Semi-finished products, long products and sheet hot-rolled products, wire rod and forgings. Chemical composition of steel S235JR according to ladle sample for thicknesses not exceeding 40 mm, %